Skip to main content

4CH Channel Optocoupler Isolation Relay Module 5V/12V/24V SCM PLC Signal Amplifier Board

4CH Channel Optocoupler Isolation Relay Module 5V/12V/24V SCM PLC Signal Amplifier Board
4CH Channel Optocoupler Isolation Relay Module 5V/12V/24V SCM PLC Signal Amplifier Board 4CH Channel Optocoupler Isolation Relay Module 5V/12V/24V SCM PLC Signal Amplifier Board 4CH Channel Optocoupler Isolation Relay Module 5V/12V/24V SCM PLC Signal Amplifier Board


Get 4CH Channel Optocoupler Isolation Relay Module 5V/12V/24V SCM PLC Signal Amplifier Board


Structural Features:
 
1. Use Hongfa relay, stable and reliable performance;
2. Compatible with two input modes of positive control and negative control;
3. Each channel has an LED action indicator for a more intuitive understanding of product performance;
4. Each channel adopts optocoupler isolation to enhance anti-interference performance and isolation performance;
5. At the same time, the power supply and the "IN" control terminal are independently controlled;
6. The module adopts the standard "DIN" rail-type installation design, which is convenient and quick to install, firm and stable.
 
Technical Parameters:
 
1. Trigger signal: DC5V / 12 / 24V (Optional)
2. Each trigger signal current: 5mA
3. Power supply voltage: DC5V / 12 / 24V
4. Each coil current: 18.8mA
5. Contact type: one normally open and one normally closed (single pole)
6. Maximum load current of each contact: 10A
7. Action time: below 12ms
8. Reset time: less than 4ms
9. Maximum switching frequency: 18000 times / hour
10. Mechanical life: more than 20 million times
11. Relay installation: plug-in type (No)
12: Module installation method: DIN standard rail installation

Positive control wiring introduction:
 
1. Power input terminal:
VCC is connected to the positive voltage, GND is connected to the negative voltage, and S / S is connected to the negative voltage
IN1, IN2 are connected to positive voltage control, IN1 controls KI terminal, IN2 controls K2 terminal
2. Control device output:
The output terminal is clearly marked with 234, 3 is a common point, 2 is normally open, and 4 is normally closed. K1, K2 means two relays work.
 
Negative control wiring introduction:
 
1. Power input terminal:
VCC is connected to the positive voltage, GND is connected to the negative voltage, and S / S is connected to the positive voltage
IN1, IN2 are connected to negative voltage control, IN1 controls KI terminal, IN2 controls K2 terminal
2. Control device output:
The output terminal is clearly marked with 234, 3 is a common point, 2 is normally open, and 4 is normally closed. KI, K2 means two relays work.

Package includes:

1 x Relay board

























4CH Channel Optocoupler Isolation Relay Module 5V/12V/24V SCM PLC Signal Amplifier Board See detail


Popular posts from this blog

TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino

Get TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino Features:   1. Main control chip uses ESP32, Tensilica dual core processor, clocked at 240 MHz, computing capacity of up to 600 DMIPS, 520 SRAM, 802.11 KB chip b/g/n HT40 Wi-Fi transceiver, baseband, and LWIP protocol stack, Bluetooth (Bluetooth dual-mode integrated traditional and BLE low-power Bluetooth) 2. Onboard 4 M bytes (32 M bit) , flash, and Wi-Fi antennas 3. 0.96-inch White OLED display 4. Lithium battery charging circuit and interface 5. CP2102 USB to serial chip, perfect support for Arduino development   Package includes:   1 x ESP32 OLED V2.0 1 x line ​2 x pin TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino See detail
Read more

No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock

Get No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock Features: ● It is suitable only for a wooden door, especially for a drawer, locker, cabinet, sliding door. ● No need to drill holes, no damage to your cabinet. ● Auto return and auto lock function, easy operation. ● Stainless steel latch and ABS plastic case, durable and anti-corrosion. Specifications: - Material: stainless steel - Type: 1 key/2keys - Lock case material: ABS plastic - Accept the thickness of the cabinet door or wardorbe: within 50 mm. - Only suitable for wooden door - Power supply: 4x AA batteries. Package Included: 1 x No-hole Cabinet Lock 1 x Key(1 key/2keys optional) 1 Set Accessory Details Pictures: No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock See detail
Read more

433MHz AC 220V 2 Channel Wireless Remote Control Switch Module AK-RK02S-220B+AK-1000-3F Remote Control Transmitter

Get 433MHz AC 220V 2 Channel Wireless Remote Control Switch Module AK-RK02S-220B+AK-1000-3F Remote Control Transmitter Features: 220V 2 channel learning code remote control switch adopts 10A relay, which can load large power electrical appliances; learning MCU decodes and can learn multiple remote controllers; simple and flexible operation; output mode can be switched by short connection reserved solder pad, and point, self-lock and interlock can be selected and used arbitrarily, which is suitable for many applications in many fields; reserved data bit output adjustment port, can be used. By choosing the corresponding key position value of remote control in different positions, it is convenient for customers to match all kinds of remote control they like, and avoids the embarrassment of the old fixed key position matching only a single style remote control. Output without voltage, easy to install.   Specification: Operating Voltage: AC220V W...
Read more