MSI.SDR Panadapter SDR Receiver 10kHz to 2GHz Built-in TCXO For SDRPlay RSP1 Raspberry Pi 2/3 12-bit ADC H4-003

Get MSI.SDR Panadapter SDR Receiver 10kHz to 2GHz Built-in TCXO For SDRPlay RSP1 Raspberry Pi 2/3 12-bit ADC H4-003

Description:

Covers frequencies from 10KHz to 2GHz. Just connect a PC and an antenna. The function of the receiver can be provided.
Compatible with all SDRPlay RSP1 software. Compatible with popular SDR software platforms You can monitor up to 10 MHz of spectrum simultaneously. Enjoy all modes of operation. Small size and easy to carry. Frequency from LF long wave to HF short wave VHF UHF microwave contains all amateur radio bands

Main Feature:

1. Exquisite and sturdy aluminum casing
2. Frequency continuous coverage from 10kHz to 2GHz
3. 12-bit ADC chip (not the kind of RTL chip)
4. Built-in front end filter
5. Built-in TCXO (temperature-compensated crystal oscillator) 0.5ppm
6. Spectrum bandwidth of up to 10Mhz
7. Higher sensitivity and good selectivity
8. More often low background noise
9. Simple USB interface (micor jack)
10. SMA antenna connector
11. USB power supply No separate power supply
12. Compatible with all SDRPlay RSP1 software.
13. Weight :25g

Feature:

It can receive HF short wave directly without the need of upconverter.
Covers all amateur bands, aeronautical bands LF to HF, VHF, UHF
It is possible to see the entire amateur band spectrum at the same time.
Support mainstream SDR software,(including HDSDR, SDRConsole, SDR#, SDRuno, etc.)
Available ExtIO-based plugins
Support for multi-system platforms, including Windows, Linux, Mac, Android, Raspberry Pi 2/3

Package included:

1 x MsiSDR host

MSI.SDR Panadapter SDR Receiver 10kHz to 2GHz Built-in TCXO For SDRPlay RSP1 Raspberry Pi 2/3 12-bit ADC H4-003 See detail

3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module

Get 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module Features: BME280, the precision sensor from , is soldered onto PCB. Not only the pressure and the temperature, this sensor can measure humidity. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface High precision, ultra-low power consumption pressure sensors, can be applied to mobile devices. Specifications: Operating voltage: 3.3 V Pressure ranges: 300-1100 hPa (equivalent to + 9000 ...- 500 m above / below sea level) Relative accuracy: ± 12 hPa (equivalent to ± 1 m 950 ~ 1050hPa @ 25 ° C) Absolute precision type: ± 1 hPa (950 ... 1050 hPa, 0 ~+ 40 ° C) Offset temperature coefficient: 1.5 Pa / K, equiv. At 12.6 cm / K (25 ~ 40 ° C at 900 hPa) Temperature range: -40- + 85 ° C PCB Size: 15.5 x 11.5 mm Package Included: 3 x BMP280 Digital Sensor Module 3 x 6P Pin 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pre...

No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock

Get No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock Features: ● It is suitable only for a wooden door, especially for a drawer, locker, cabinet, sliding door. ● No need to drill holes, no damage to your cabinet. ● Auto return and auto lock function, easy operation. ● Stainless steel latch and ABS plastic case, durable and anti-corrosion. Specifications: - Material: stainless steel - Type: 1 key/2keys - Lock case material: ABS plastic - Accept the thickness of the cabinet door or wardorbe: within 50 mm. - Only suitable for wooden door - Power supply: 4x AA batteries. Package Included: 1 x No-hole Cabinet Lock 1 x Key(1 key/2keys optional) 1 Set Accessory Details Pictures: No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock See detail

TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino

Get TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino Features: 1. Main control chip uses ESP32, Tensilica dual core processor, clocked at 240 MHz, computing capacity of up to 600 DMIPS, 520 SRAM, 802.11 KB chip b/g/n HT40 Wi-Fi transceiver, baseband, and LWIP protocol stack, Bluetooth (Bluetooth dual-mode integrated traditional and BLE low-power Bluetooth) 2. Onboard 4 M bytes (32 M bit) , flash, and Wi-Fi antennas 3. 0.96-inch White OLED display 4. Lithium battery charging circuit and interface 5. CP2102 USB to serial chip, perfect support for Arduino development Package includes: 1 x ESP32 OLED V2.0 1 x line 2 x pin TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino See detail

Yuna Maslova

Search This Blog