DIY 6J1 Tube Preamp Amplifier Board Pre-amp Headphone Amp 6J1 Valve Preamp Bile Buffer diy Kits With 12v Dual Power Shell Speaker

Get DIY 6J1 Tube Preamp Amplifier Board Pre-amp Headphone Amp 6J1 Valve Preamp Bile Buffer diy Kits With 12v Dual Power Shell Speaker

Description:

Model: 6j1 Tube
Channel type: 2.0 / Stereo
Operating voltage: AC12V 0
Board size: 80*100mm

Name	Parameter	PCB mark	Quantity
Resistor	1K	R2 R4 R30 R31	4
	100K	R16 R19	2
	4.7K	R1 R3 R10 R13 R17 R18 R20 R21	8
	47R	R5-R8	4
	47R/3W	R9	1
	470K	R11 R14	2
	56K	R22 R23	2
	200R	R12 R15	2
	22K	R24 R26 R27 R32	4
	10R	R25 R28	2
Capacitor	47uF/10V	C13 C14	2
	470uF/35V	C5-C8	4
	2200UF/25V4	C1-C4	4
Film capacitor	1uF/50V	C9-C12	4
Film capacitor	0.1uF(104)/50V	C15 C16	2
Transistor	D667	Q1 Q4	2
Transistor	B647	Q2 Q3	2
Terminal block	2p	J1 J2	2
Terminal block	3p	GND	1
Audio block	3.5MM	J3 J4	2
LED	3mm Blue	D1 D2	2
Rectifier bridge	KBJ608	P1	1
Electronic Tube	6J1	D1 D2	2
Electronic Tube socket	7pin	D1 D2	2
Double potentiometer	50K	RP	1
Power amplifier chip	lm1875	U1 U2	2
Screw	M3*5		2
Potentiometer cap			1
Heatsink			1
Insulating sheet			2
PCB			1

Package included:

1 x DIY 6J1 Tube Preamp Amplifier Board Kits
1 x 12V dual power supply
1 x shell case
2 x speaker

DIY 6J1 Tube Preamp Amplifier Board Pre-amp Headphone Amp 6J1 Valve Preamp Bile Buffer diy Kits With 12v Dual Power Shell Speaker See detail

3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module

Get 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module Features: BME280, the precision sensor from , is soldered onto PCB. Not only the pressure and the temperature, this sensor can measure humidity. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface High precision, ultra-low power consumption pressure sensors, can be applied to mobile devices. Specifications: Operating voltage: 3.3 V Pressure ranges: 300-1100 hPa (equivalent to + 9000 ...- 500 m above / below sea level) Relative accuracy: ± 12 hPa (equivalent to ± 1 m 950 ~ 1050hPa @ 25 ° C) Absolute precision type: ± 1 hPa (950 ... 1050 hPa, 0 ~+ 40 ° C) Offset temperature coefficient: 1.5 Pa / K, equiv. At 12.6 cm / K (25 ~ 40 ° C at 900 hPa) Temperature range: -40- + 85 ° C PCB Size: 15.5 x 11.5 mm Package Included: 3 x BMP280 Digital Sensor Module 3 x 6P Pin 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pre...

No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock

Get No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock Features: ● It is suitable only for a wooden door, especially for a drawer, locker, cabinet, sliding door. ● No need to drill holes, no damage to your cabinet. ● Auto return and auto lock function, easy operation. ● Stainless steel latch and ABS plastic case, durable and anti-corrosion. Specifications: - Material: stainless steel - Type: 1 key/2keys - Lock case material: ABS plastic - Accept the thickness of the cabinet door or wardorbe: within 50 mm. - Only suitable for wooden door - Power supply: 4x AA batteries. Package Included: 1 x No-hole Cabinet Lock 1 x Key(1 key/2keys optional) 1 Set Accessory Details Pictures: No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock See detail

TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino

Get TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino Features: 1. Main control chip uses ESP32, Tensilica dual core processor, clocked at 240 MHz, computing capacity of up to 600 DMIPS, 520 SRAM, 802.11 KB chip b/g/n HT40 Wi-Fi transceiver, baseband, and LWIP protocol stack, Bluetooth (Bluetooth dual-mode integrated traditional and BLE low-power Bluetooth) 2. Onboard 4 M bytes (32 M bit) , flash, and Wi-Fi antennas 3. 0.96-inch White OLED display 4. Lithium battery charging circuit and interface 5. CP2102 USB to serial chip, perfect support for Arduino development Package includes: 1 x ESP32 OLED V2.0 1 x line 2 x pin TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino See detail

Yuna Maslova

Search This Blog