DC PWM Motor Speed Controller Module LED Digital Display Switch Accelerate Decelerate Speed Control Regulator DC8V-55V

Get DC PWM Motor Speed Controller Module LED Digital Display Switch Accelerate Decelerate Speed Control Regulator DC8V-55V

Specifications:

Voltage: DC8V-55V (wide voltage anti-back protection)

Speed range: long press / short press to adjust the degree, 0% -100% speed

Drive current: up to 10A, (recommended output series 12A fuse)

Standby current: <17mA

Mounting hole: diameter 3mm

Product size: 64mm*35mm*19mm (length * width * height)

Working temperature: -20 ° C ~ 70 ° C

Features:

1. The digital tube flashes at the moment of power-on (normal phenomenon, no need to worry)

2. close to the limit drive current working conditions, it is recommended to take the output end of the fuse

3. The DC motor speed controller cannot be installed in places where there is dripping water and children can reach it.

4. After wiring, check if the line is correct and then energize, so as to avoid accidentally burning the temperature controller and load device.

Wiring:

“M+” and “M-” are respectively connected to the positive and negative terminals of the output, M+ is positive and M- is negative.

“VIN” and “GND” are respectively connected to the positive and negative terminals of the input terminal, Vin is positive and GND is negative (input power supply voltage is DC8V-55V)

Instructions:

1. Click/long press the “speed increase” button to increase the motor speed to 100%.

2. Click/long press the “speed down” button to increase the motor speed to a minimum of 0%.

3. Press and hold the “Power On/Off” button for one second, the controller will be turned on or off (the power is turned off by default, and the memory function is activated after booting)

Package Included:

1 X DC 8V-55V 10A Motor Speed Controller

DC PWM Motor Speed Controller Module LED Digital Display Switch Accelerate Decelerate Speed Control Regulator DC8V-55V See detail

3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module

Get 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module Features: BME280, the precision sensor from , is soldered onto PCB. Not only the pressure and the temperature, this sensor can measure humidity. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface High precision, ultra-low power consumption pressure sensors, can be applied to mobile devices. Specifications: Operating voltage: 3.3 V Pressure ranges: 300-1100 hPa (equivalent to + 9000 ...- 500 m above / below sea level) Relative accuracy: ± 12 hPa (equivalent to ± 1 m 950 ~ 1050hPa @ 25 ° C) Absolute precision type: ± 1 hPa (950 ... 1050 hPa, 0 ~+ 40 ° C) Offset temperature coefficient: 1.5 Pa / K, equiv. At 12.6 cm / K (25 ~ 40 ° C at 900 hPa) Temperature range: -40- + 85 ° C PCB Size: 15.5 x 11.5 mm Package Included: 3 x BMP280 Digital Sensor Module 3 x 6P Pin 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pre...

No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock

Get No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock Features: ● It is suitable only for a wooden door, especially for a drawer, locker, cabinet, sliding door. ● No need to drill holes, no damage to your cabinet. ● Auto return and auto lock function, easy operation. ● Stainless steel latch and ABS plastic case, durable and anti-corrosion. Specifications: - Material: stainless steel - Type: 1 key/2keys - Lock case material: ABS plastic - Accept the thickness of the cabinet door or wardorbe: within 50 mm. - Only suitable for wooden door - Power supply: 4x AA batteries. Package Included: 1 x No-hole Cabinet Lock 1 x Key(1 key/2keys optional) 1 Set Accessory Details Pictures: No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock See detail

TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino

Get TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino Features: 1. Main control chip uses ESP32, Tensilica dual core processor, clocked at 240 MHz, computing capacity of up to 600 DMIPS, 520 SRAM, 802.11 KB chip b/g/n HT40 Wi-Fi transceiver, baseband, and LWIP protocol stack, Bluetooth (Bluetooth dual-mode integrated traditional and BLE low-power Bluetooth) 2. Onboard 4 M bytes (32 M bit) , flash, and Wi-Fi antennas 3. 0.96-inch White OLED display 4. Lithium battery charging circuit and interface 5. CP2102 USB to serial chip, perfect support for Arduino development Package includes: 1 x ESP32 OLED V2.0 1 x line 2 x pin TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino See detail

Yuna Maslova

Search This Blog