Skip to main content

M5Stack® Wireless GSM Module SIM800L Stackable IoT Development Board for Arduino ESP32 with MIC & 3.5mm Headphone Jack

M5Stack® Wireless GSM Module SIM800L Stackable IoT Development Board for Arduino ESP32 with MIC & 3.5mm Headphone Jack
M5Stack® Wireless GSM Module SIM800L Stackable IoT Development Board for Arduino ESP32 with MIC & 3.5mm Headphone Jack M5Stack® Wireless GSM Module SIM800L Stackable IoT Development Board for Arduino ESP32 with MIC & 3.5mm Headphone Jack M5Stack® Wireless GSM Module SIM800L Stackable IoT Development Board for Arduino ESP32 with MIC & 3.5mm Headphone Jack


Get M5Stack® Wireless GSM Module SIM800L Stackable IoT Development Board for Arduino ESP32 with MIC & 3.5mm Headphone Jack


Description:

SIM800L is a cellular phone module, integrated SIM800L, a GSM/GPRS module, only cpmpatible with 2G network. if you want to integrate a cellular module into your design with vioce, text and SMS, this hand-solderable module is pretty nice!

Series Protocol: UART

Product Features:

  • 3.5 mm phone audio jack
  • MIC (MIC is disable by default. To enable it, you will need to weld a 0 ohm resistor at MIC-EN )
  • Supply voltage: 3.8V - 4.2V
  • Recommended supply voltage: 4V
  • Power consumption: sleep mode < 2.0mA idle mode < 7.0mA GSM transmission (a v g): 350 mA GSM transmission (peek): 2000mA
  • Module size: 25 x 23 mm
  • Interface: UART (max. 2.8V) and AT commands
  • SIM card socket: microSIM (bottom side)
  • Supported frequencies: Quad Band (850 / 950 / 1800 /1900 MHz)
  • Antenna connector: IPX
  • Spring Antenna on board
  • Status signaling: LED
  • Working temperature ran ge: -40 do + 85 ° C
  • Product Size: 54.2mm x 54.2mm x 12.8mm
  • Product weight: 16.5g

PinMap:

SIM800

SIM800 Pin ESP32 Chip
TXD U2RXD(GPIO16)
RXD U2TXD(GPIO17)
RST GPIO5

Paxkage Included:

  • 1x M5Stack SIM800L Module

Applications:

  • Nitrogen dioxide alarm
  • Automatic Web Spider SMS-notifier
  • Remote meter reading system

EasyLoader

1.EasyLoader is a simple and fast program burner, and each product page has a product-related case program for EasyLoader.

2.After downloading the software, double-click to run the application, connect the M5 device to the computer via the data cable, select the port parameters, and click "Burn" to start burning.

      3.The CP210X (USB driver) needs to be installed before the EasyLoader is burned. Click here to view the driver installation tutorial

Schematic:














M5Stack® Wireless GSM Module SIM800L Stackable IoT Development Board for Arduino ESP32 with MIC & 3.5mm Headphone Jack See detail


Popular posts from this blog

3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module

Get 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module Features:   BME280, the precision sensor from , is soldered onto PCB. Not only the pressure and the temperature, this sensor can measure humidity. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface High precision, ultra-low power consumption pressure sensors, can be applied to mobile devices.   Specifications:   Operating voltage: 3.3 V Pressure ranges: 300-1100 hPa (equivalent to + 9000 ...- 500 m above / below sea level) Relative accuracy: ± 12 hPa (equivalent to ± 1 m 950 ~ 1050hPa @ 25 ° C) Absolute precision type: ± 1 hPa (950 ... 1050 hPa, 0 ~+ 40 ° C) Offset temperature coefficient: 1.5 Pa / K, equiv. At 12.6 cm / K (25 ~ 40 ° C at 900 hPa) Temperature range: -40- + 85 ° C PCB Size: 15.5 x 11.5 mm   Package Included:   3 x BMP280 Digital Sensor Module 3 x 6P Pin 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pre...
Read more

TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino

Get TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino Features:   1. Main control chip uses ESP32, Tensilica dual core processor, clocked at 240 MHz, computing capacity of up to 600 DMIPS, 520 SRAM, 802.11 KB chip b/g/n HT40 Wi-Fi transceiver, baseband, and LWIP protocol stack, Bluetooth (Bluetooth dual-mode integrated traditional and BLE low-power Bluetooth) 2. Onboard 4 M bytes (32 M bit) , flash, and Wi-Fi antennas 3. 0.96-inch White OLED display 4. Lithium battery charging circuit and interface 5. CP2102 USB to serial chip, perfect support for Arduino development   Package includes:   1 x ESP32 OLED V2.0 1 x line ​2 x pin TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino See detail
Read more

No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock

Get No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock Features: ● It is suitable only for a wooden door, especially for a drawer, locker, cabinet, sliding door. ● No need to drill holes, no damage to your cabinet. ● Auto return and auto lock function, easy operation. ● Stainless steel latch and ABS plastic case, durable and anti-corrosion. Specifications: - Material: stainless steel - Type: 1 key/2keys - Lock case material: ABS plastic - Accept the thickness of the cabinet door or wardorbe: within 50 mm. - Only suitable for wooden door - Power supply: 4x AA batteries. Package Included: 1 x No-hole Cabinet Lock 1 x Key(1 key/2keys optional) 1 Set Accessory Details Pictures: No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock See detail
Read more