Skip to main content

ICL7107 Voltmeter DIY Electronic Production Kit DC5V 35mA Voltage Meter Digital Voltmeter

ICL7107 Voltmeter DIY Electronic Production Kit DC5V 35mA Voltage Meter Digital Voltmeter
ICL7107 Voltmeter DIY Electronic Production Kit DC5V 35mA Voltage Meter Digital Voltmeter ICL7107 Voltmeter DIY Electronic Production Kit DC5V 35mA Voltage Meter Digital Voltmeter ICL7107 Voltmeter DIY Electronic Production Kit DC5V 35mA Voltage Meter Digital Voltmeter


Get ICL7107 Voltmeter DIY Electronic Production Kit DC5V 35mA Voltage Meter Digital Voltmeter


Description:

Kit Name: ICL7107 Voltmeter DIY Kit
PCB size: 70.6*39mm
Head mounting opening size: 77*40mm
Display window size: 51*24mm
Soldering manual: Click here.

Electrical parameters:
 
Working voltage: DC5V
Working current: 35mA
Measurement accuracy: It can be calibrated to get higher precision and no parameters at present.
Measuring range: divided into 3 files, 0-2V file Measuring small voltage
                                                            0-20V file measuring low voltage
                                                            0-200V, measuring higher voltage.
Range selection method: solder joints with gear selection on the board,
When the two points of the 0-2V file are soldered together, and the resistance of the RX soldering resistor is 1K, the measurement range is 0-2V;
When soldering 2 points of 0-20V file together, the RX soldering resistance is 100K, the measuring range is 0-20V;
When soldering 2 points of 0-200V file together, the RX soldering resistance is 1M, the measurement range is 0-200V;
Overrange display: first position shows 1 or -1
In the kit, the RX is available in 100K and 1M, and the buyer selects the soldering according to his measurement range. This voltmeter can also be changed into an ammeter. The method of changing the current meter: the PCB reserve a 2W 0.1 ohm high-precision resistance soldering position on the board, solder this resistance, and then RX does not need to be soldered. This is a 0-2A ammeter.
Display color: red
Tools needed to make the production: multimeters, electric irons, and water pliers are needed.

Package included:

1 x PCB board
3 x 1N4148
1 x 5.1V Zener Diode
1 x 100 ohm resistor
1 x 270 ohm resistor
2 x 2K resistor
1 x 20K resistor
1 x 47K resistor
1 x 56K resistor
2 x 100K resistor
1 x 1M resistor
1 x 2.2MH inductor
2 x 104 monolithic capacitor
2 x 101 monolithic capacitor
1 x 224 monolithic capacitor
1 x 474 monolithic capacitor
2 x 10UF25V electrolytic capacitor
1 x C1815
1 x TL431
2 x 3296-202 potentiometer
1 x XH2.54-2P straight seat
1 x XH2.54-2P line
1 x KF301-2 seat
1 x 40P chip holder
1 x LT7107 chip
4 x 0.56 one common digital tube
1 x case
4 x M2*6 self-tapping screws






















ICL7107 Voltmeter DIY Electronic Production Kit DC5V 35mA Voltage Meter Digital Voltmeter See detail


Popular posts from this blog

3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module

Get 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pressure Sensor Module Features:   BME280, the precision sensor from , is soldered onto PCB. Not only the pressure and the temperature, this sensor can measure humidity. It uses both I2C and SPI (supports 3-, 4-wire SPI) interface High precision, ultra-low power consumption pressure sensors, can be applied to mobile devices.   Specifications:   Operating voltage: 3.3 V Pressure ranges: 300-1100 hPa (equivalent to + 9000 ...- 500 m above / below sea level) Relative accuracy: ± 12 hPa (equivalent to ± 1 m 950 ~ 1050hPa @ 25 ° C) Absolute precision type: ± 1 hPa (950 ... 1050 hPa, 0 ~+ 40 ° C) Offset temperature coefficient: 1.5 Pa / K, equiv. At 12.6 cm / K (25 ~ 40 ° C at 900 hPa) Temperature range: -40- + 85 ° C PCB Size: 15.5 x 11.5 mm   Package Included:   3 x BMP280 Digital Sensor Module 3 x 6P Pin 3pcs BME280 Digital Sensor Temperature Humidity Atmospheric Pre...
Read more

TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino

Get TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino Features:   1. Main control chip uses ESP32, Tensilica dual core processor, clocked at 240 MHz, computing capacity of up to 600 DMIPS, 520 SRAM, 802.11 KB chip b/g/n HT40 Wi-Fi transceiver, baseband, and LWIP protocol stack, Bluetooth (Bluetooth dual-mode integrated traditional and BLE low-power Bluetooth) 2. Onboard 4 M bytes (32 M bit) , flash, and Wi-Fi antennas 3. 0.96-inch White OLED display 4. Lithium battery charging circuit and interface 5. CP2102 USB to serial chip, perfect support for Arduino development   Package includes:   1 x ESP32 OLED V2.0 1 x line ​2 x pin TTGO 0.96 Inch ESP32 V2.0 OLED WiFi Module + Bluetooth Double ESP-32 et OLED 4 MB For Arduino See detail
Read more

No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock

Get No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock Features: ● It is suitable only for a wooden door, especially for a drawer, locker, cabinet, sliding door. ● No need to drill holes, no damage to your cabinet. ● Auto return and auto lock function, easy operation. ● Stainless steel latch and ABS plastic case, durable and anti-corrosion. Specifications: - Material: stainless steel - Type: 1 key/2keys - Lock case material: ABS plastic - Accept the thickness of the cabinet door or wardorbe: within 50 mm. - Only suitable for wooden door - Power supply: 4x AA batteries. Package Included: 1 x No-hole Cabinet Lock 1 x Key(1 key/2keys optional) 1 Set Accessory Details Pictures: No-hole Sensor Cabinet Lock Electronic Hidden Home Furniture Door Drawers Lock See detail
Read more